diff --git a/arch/arm64/boot/dts/marvell/mmp/pxa1908-samsung-coreprimevelte.dts b/arch/arm64/boot/dts/marvell/mmp/pxa1908-samsung-coreprimevelte.dts
index 47a4f01a7077..b2ce5edd9c6a 100644
--- a/arch/arm64/boot/dts/marvell/mmp/pxa1908-samsung-coreprimevelte.dts
+++ b/arch/arm64/boot/dts/marvell/mmp/pxa1908-samsung-coreprimevelte.dts
@@ -10,6 +10,7 @@ / {
 	aliases {
 		mmc0 = &sdh2; /* eMMC */
 		mmc1 = &sdh0; /* SD card */
+		mmc2 = &sdh1; /* SDIO */
 		serial0 = &uart0;
 	};
 
@@ -23,6 +24,7 @@ chosen {
 		fb0: framebuffer@17177000 {
 			compatible = "simple-framebuffer";
 			reg = <0 0x17177000 0 (480 * 800 * 4)>;
+			power-domains = <&apmu PXA1908_POWER_DOMAIN_DSI>;
 			width = <480>;
 			height = <800>;
 			stride = <(480 * 4)>;
@@ -30,46 +32,26 @@ fb0: framebuffer@17177000 {
 		};
 	};
 
-	/* Bootloader fills this in */
 	memory@0 {
 		device_type = "memory";
-		reg = <0 0 0 0>;
+		reg = <0 0 0 0x40000000>;
 	};
 
 	reserved-memory {
-		#address-cells = <2>;
-		#size-cells = <2>;
-		ranges;
+		/*
+		 * Reserved by the vendor bootloader as a "secure region".
+		 *
+		 * TODO: See if the responsible stage of the bootloader can be
+		 * replaced
+		 */
+		secure-region@0 {
+			reg = <0 0 0 0x1000000>;
+		};
 
 		framebuffer@17000000 {
 			reg = <0 0x17000000 0 0x1800000>;
 			no-map;
 		};
-
-		gpu@9000000 {
-			reg = <0 0x9000000 0 0x1000000>;
-		};
-
-		/* Communications processor, aka modem */
-		cp@5000000 {
-			reg = <0 0x5000000 0 0x3000000>;
-		};
-
-		cm3@a000000 {
-			reg = <0 0xa000000 0 0x80000>;
-		};
-
-		seclog@8000000 {
-			reg = <0 0x8000000 0 0x100000>;
-		};
-
-		ramoops@8100000 {
-			compatible = "ramoops";
-			reg = <0 0x8100000 0 0x40000>;
-			record-size = <0x8000>;
-			console-size = <0x20000>;
-			max-reason = <5>;
-		};
 	};
 
 	i2c-muic {
@@ -88,6 +70,12 @@ muic: extcon@14 {
 			reg = <0x14>;
 			interrupt-parent = <&gpio>;
 			interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+
+			usb_con: connector {
+				compatible = "usb-b-connector";
+				label = "micro-USB";
+				type = "micro";
+			};
 		};
 	};
 
@@ -115,6 +103,21 @@ key-voldown {
 			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
 		};
 	};
+
+	backlight {
+		compatible = "kinetic,ktd2801";
+		ctrl-gpios = <&gpio 97 GPIO_ACTIVE_HIGH>;
+		max-brightness = <210>;
+	};
+
+	vibrator {
+		compatible = "pwm-vibrator";
+		pwm-names = "enable";
+		pwms = <&pwm3 100000>;
+		enable-gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vibrator_pin>;
+	};
 };
 
 &smmu {
@@ -286,6 +289,151 @@ sdh0_pins_2: sdh0-pins-2 {
 		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
 		pinctrl-single,low-power-mode = <0x208 0x388>;
 	};
+
+	sdh1_pins_0: sdh1-pins-0 {
+		pinctrl-single,pins = <
+			0x170 1
+			0x174 1
+			0x178 1
+			0x17c 1
+			0x180 1
+		>;
+		pinctrl-single,drive-strength = <0x1000 0x1800>;
+		pinctrl-single,bias-pullup = <0 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0 0xa000 0 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0 0x388>;
+	};
+
+	sdh1_pins_1: sdh1-pins-1 {
+		pinctrl-single,pins = <0x184 1>;
+		pinctrl-single,drive-strength = <0 0x1800>;
+		pinctrl-single,bias-pullup = <0 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0 0xa000 0 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0x208 0x388>;
+	};
+
+	sdh1_pins_2: sdh1-pins-2 {
+		pinctrl-single,pins = <0xec 0>;
+		pinctrl-single,drive-strength = <0x1000 0x1800>;
+		pinctrl-single,bias-pullup = <0x8000 0x8000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0x8000 0x8000 0 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0 0x388>;
+	};
+
+	sdh1_fast_pins_0: sdh1-fast-pins-0 {
+		pinctrl-single,pins = <
+			0x170 1
+			0x174 1
+			0x178 1
+			0x17c 1
+			0x180 1
+		>;
+		pinctrl-single,drive-strength = <0x1800 0x1800>;
+		pinctrl-single,bias-pullup = <0 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0 0xa000 0 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0 0x388>;
+	};
+
+	sdh1_fast_pins_1: sdh1-fast-pins-1 {
+		pinctrl-single,pins = <0x184 1>;
+		pinctrl-single,drive-strength = <0x1800 0x1800>;
+		pinctrl-single,bias-pullup = <0 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0 0xa000 0 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0x208 0x388>;
+	};
+
+	sdh2_pins_0: sdh2-pins-0 {
+		pinctrl-single,pins = <
+			0x24 1
+			0x28 1
+			0x2c 1
+			0x30 1
+			0x34 1
+			0x38 1
+			0x3c 1
+			0x40 1
+		>;
+		pinctrl-single,drive-strength = <0x1000 0x1800>;
+		pinctrl-single,bias-pullup = <0 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0 0xa000 0 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0 0x388>;
+	};
+
+	sdh2_pins_1: sdh2-pins-1 {
+		pinctrl-single,pins = <0x64 1>;
+		pinctrl-single,drive-strength = <0x1000 0x1800>;
+		pinctrl-single,bias-pullup = <0 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0 0xa000 0 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0x208 0x388>;
+	};
+
+	sdh2_pins_2: sdh2-pins-2 {
+		pinctrl-single,pins = <0x5c 1>;
+		pinctrl-single,bias-pullup = <0xc000 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0x8000 0xa000 0x8000 0xa000>;
+		pinctrl-single,low-power-mode = <0x288 0x388>;
+	};
+
+	sdh2_fast_pins_0: sdh2-fast-pins-0 {
+		pinctrl-single,pins = <
+			0x24 1
+			0x28 1
+			0x2c 1
+			0x30 1
+			0x34 1
+			0x38 1
+			0x3c 1
+			0x40 1
+		>;
+		pinctrl-single,drive-strength = <0x1800 0x1800>;
+		pinctrl-single,bias-pullup = <0 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0 0xa000 0 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0 0x388>;
+	};
+
+	sdh2_fast_pins_1: sdh2-fast-pins-1 {
+		pinctrl-single,pins = <0x64 1>;
+		pinctrl-single,drive-strength = <0x1800 0x1800>;
+		pinctrl-single,bias-pullup = <0 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0 0xa000 0 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0x208 0x388>;
+	};
+
+	sdh2_fast_pins_2: sdh2-fast-pins-2 {
+		pinctrl-single,pins = <0x5c 1>;
+		pinctrl-single,drive-strength = <0x1800 0x1800>;
+		pinctrl-single,bias-pullup = <0xc000 0xc000 0 0xc000>;
+		pinctrl-single,bias-pulldown = <0x8000 0xa000 0x8000 0xa000>;
+		pinctrl-single,low-power-mode = <0x288 0x388>;
+	};
+
+	vibrator_pin: vibrator-pin {
+		pinctrl-single,pins = <0x12c 0>;
+		pinctrl-single,drive-strength = <0x1000 0x1800>;
+		pinctrl-single,bias-pullup = <0x8000 0xc000 0x8000 0xc000>;
+		pinctrl-single,bias-pulldown = <0xa000 0xa000 0 0xa000>;
+		pinctrl-single,input-schmitt = <0 0x30>;
+		pinctrl-single,input-schmitt-enable = <0x40 0 0x40 0x40>;
+		pinctrl-single,low-power-mode = <0 0x388>;
+	};
 };
 
 &uart0 {
@@ -303,10 +451,46 @@ &twsi1 {
 
 &twsi2 {
 	status = "okay";
+
+	pmic@30 {
+		compatible = "marvell,88pm886-a1";
+		reg = <0x30>;
+		interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+		wakeup-source;
+
+		regulators {
+			ldo2: ldo2 {
+				regulator-min-microvolt = <1900000>;
+				regulator-max-microvolt = <3100000>;
+			};
+
+			ldo6: ldo6 {
+				regulator-boot-on;
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			ldo14: ldo14 {
+				regulator-boot-on;
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
 };
 
 &twsi3 {
 	status = "okay";
+
+	touchscreen@50 {
+		compatible = "imagis,ist3032c";
+		reg = <0x50>;
+		interrupt-parent = <&gpio>;
+		interrupts = <72 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&ldo2>;
+		touchscreen-size-x = <480>;
+		touchscreen-size-y = <800>;
+	};
 };
 
 &usb {
@@ -314,18 +498,33 @@ &usb {
 };
 
 &sdh2 {
-	/* Disabled for now because initialization fails with -ETIMEDOUT. */
-	status = "disabled";
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&sdh2_pins_0 &sdh2_pins_1 &sdh2_pins_2>;
+	pinctrl-1 = <&sdh2_fast_pins_0 &sdh2_fast_pins_1 &sdh2_fast_pins_2>;
 	bus-width = <8>;
 	non-removable;
 	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
 };
 
 &sdh0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&sdh0_pins_0 &sdh0_pins_1 &sdh0_pins_2>;
-	cd-gpios = <&gpio 11 0>;
-	cd-inverted;
+	cd-gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
 	bus-width = <4>;
 	wp-inverted;
+	vmmc-supply = <&ldo14>;
+	vqmmc-supply = <&ldo6>;
+};
+
+&sdh1 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&sdh1_pins_0 &sdh1_pins_1 &sdh1_pins_2>;
+	pinctrl-1 = <&sdh1_fast_pins_0 &sdh1_fast_pins_1 &sdh1_pins_2>;
+	bus-width = <4>;
+	non-removable;
+};
+
+&pwm3 {
+	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/marvell/mmp/pxa1908.dtsi b/arch/arm64/boot/dts/marvell/mmp/pxa1908.dtsi
index cf2b9109688c..5778bfdb8567 100644
--- a/arch/arm64/boot/dts/marvell/mmp/pxa1908.dtsi
+++ b/arch/arm64/boot/dts/marvell/mmp/pxa1908.dtsi
@@ -3,6 +3,7 @@
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/marvell,pxa1908.h>
+#include <dt-bindings/power/marvell,pxa1908-power.h>
 
 / {
 	model = "Marvell Armada PXA1908";
@@ -58,6 +59,20 @@ psci {
 		method = "smc";
 	};
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ramoops@8100000 {
+			compatible = "ramoops";
+			reg = <0 0x8100000 0 0x40000>;
+			record-size = <0x8000>;
+			console-size = <0x20000>;
+			max-reason = <5>;
+		};
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
@@ -79,6 +94,7 @@ smmu: iommu@c0010000 {
 			#iommu-cells = <1>;
 			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
 				<GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+			power-domains = <&apmu PXA1908_POWER_DOMAIN_VPU>;
 			status = "disabled";
 		};
 
@@ -195,6 +211,38 @@ gpio@100 {
 				};
 			};
 
+			pwm0: pwm@1a000 {
+				compatible = "marvell,pxa250-pwm";
+				reg = <0x1a000 0x10>;
+				clocks = <&apbc PXA1908_CLK_PWM0>;
+				#pwm-cells = <1>;
+				status = "disabled";
+			};
+
+			pwm1: pwm@1a400 {
+				compatible = "marvell,pxa250-pwm";
+				reg = <0x1a400 0x10>;
+				clocks = <&apbc PXA1908_CLK_PWM1>;
+				#pwm-cells = <1>;
+				status = "disabled";
+			};
+
+			pwm2: pwm@1a800 {
+				compatible = "marvell,pxa250-pwm";
+				reg = <0x1a800 0x10>;
+				clocks = <&apbc PXA1908_CLK_PWM2>;
+				#pwm-cells = <1>;
+				status = "disabled";
+			};
+
+			pwm3: pwm@1ac00 {
+				compatible = "marvell,pxa250-pwm";
+				reg = <0x1ac00 0x10>;
+				clocks = <&apbc PXA1908_CLK_PWM3>;
+				#pwm-cells = <1>;
+				status = "disabled";
+			};
+
 			pmx: pinmux@1e000 {
 				compatible = "marvell,pxa1908-padconf", "pinconf-single";
 				reg = <0x1e000 0x330>;
@@ -291,9 +339,10 @@ sdh2: mmc@81000 {
 			};
 
 			apmu: clock-controller@82800 {
-				compatible = "marvell,pxa1908-apmu";
+				compatible = "marvell,pxa1908-apmu", "syscon";
 				reg = <0x82800 0x400>;
 				#clock-cells = <1>;
+				#power-domain-cells = <1>;
 			};
 		};
 	};