From 5b19ca527471903920d713bc48518a036a95bf6b Mon Sep 17 00:00:00 2001 From: Frieder Schrempf Date: Thu, 28 May 2026 12:15:56 +0200 Subject: [PATCH] arm64: dts: imx8mp-kontron: Fix GPIO for display power switch The GPIO that controls the power supply for the LVDS display connector has changed between early prototypes and the current production design of the hardware. Reflect this change in the devicetree to properly switch on the panel supply. This was working before even with the wrong GPIO due to the bidirectional level shifter used on the board which drives the EN signal high even when the input has a (weak) pull down configured as reset condition of the SoC pad. As a result the display was working but the supply was always on. Tested on BL i.MX8MP to show the correct voltage level on the level shifter input. Fixes: 946ab10e3f40 ("arm64: dts: Add support for Kontron OSM-S i.MX8MP SoM and BL carrier board") Signed-off-by: Frieder Schrempf Signed-off-by: Frank Li --- .../boot/dts/freescale/imx8mp-kontron-bl-osm-s.dts | 12 ++++++++++-- 1 file changed, 10 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mp-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mp-kontron-bl-osm-s.dts index 75ae46642782..29ce863403b8 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp-kontron-bl-osm-s.dts +++ b/arch/arm64/boot/dts/freescale/imx8mp-kontron-bl-osm-s.dts @@ -49,7 +49,9 @@ pwm-beeper { reg_vcc_panel: regulator-vcc-panel { compatible = "regulator-fixed"; - gpio = <&gpio4 3 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_vcc_panel>; + gpio = <&gpio5 3 GPIO_ACTIVE_HIGH>; enable-active-high; regulator-max-microvolt = <3300000>; regulator-min-microvolt = <3300000>; @@ -172,7 +174,7 @@ &gpio4 { &gpio5 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_gpio5>; - gpio-line-names = "I2S_BITCLK", "I2S_A_DATA_OUT", "I2S_MCLK", "PWM_2", + gpio-line-names = "I2S_BITCLK", "I2S_A_DATA_OUT", "I2S_MCLK", "VCC_PANEL_EN", "PWM_1", "PWM_0", "SPI_A_SCK", "CAN_ADDR1", "CAN_ADDR0", "SPI_A_CS0", "SPI_B_SCK", "SPI_B_SDO", "SPI_B_SDI", "SPI_B_CS0", "I2C_A_SCL", "I2C_A_SDA", @@ -329,4 +331,10 @@ MX8MP_IOMUXC_ECSPI1_MOSI__GPIO5_IO07 0x46 /* CAN_ADR0 */ MX8MP_IOMUXC_ECSPI1_MISO__GPIO5_IO08 0x46 /* CAN_ADR1 */ >; }; + + pinctrl_reg_vcc_panel: regvccpanelgrp { + fsl,pins = < + MX8MP_IOMUXC_SPDIF_TX__GPIO5_IO03 0x46 + >; + }; };