diff --git a/arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b-ovl-rp1.dts b/arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b-ovl-rp1.dts
index f0883c903527..411b58c1dddf 100644
--- a/arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b-ovl-rp1.dts
+++ b/arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b-ovl-rp1.dts
@@ -66,6 +66,18 @@ sd_vcc_reg: sd-vcc-reg {
 		enable-active-high;
 		gpios = <&gio_aon 4 GPIO_ACTIVE_HIGH>;
 	};
+
+	wl_on_reg: wl-on-reg {
+		compatible = "regulator-fixed";
+		regulator-name = "wl-on-regulator";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-0 = <&wl_on_default>;
+		pinctrl-names = "default";
+		gpio = <&gio 28 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <150000>;
+		enable-active-high;
+	};
 };
 
 &pinctrl {
@@ -79,6 +91,29 @@ pwr_button_default: pwr-button-default-state {
 		pins = "gpio20";
 		bias-pull-up;
 	};
+
+	sdio2_30_default: sdio2-30-default-state {
+		clk-pins {
+			function = "sd2";
+			pins = "gpio30";
+			bias-disable;
+		};
+		cmd-pins {
+			function = "sd2";
+			pins = "gpio31";
+			bias-pull-up;
+		};
+		dat-pins {
+			function = "sd2";
+			pins = "gpio32", "gpio33", "gpio34", "gpio35";
+			bias-pull-up;
+		};
+	};
+
+	wl_on_default: wl-on-default-state {
+		function = "gpio";
+		pins = "gpio28";
+	};
 };
 
 &pinctrl_aon {
@@ -109,6 +144,23 @@ &sdio1 {
 	cd-gpios = <&gio_aon 5 GPIO_ACTIVE_LOW>;
 };
 
+&sdio2 {
+	pinctrl-0 = <&sdio2_30_default>;
+	pinctrl-names = "default";
+	bus-width = <4>;
+	vmmc-supply = <&wl_on_reg>;
+	sd-uhs-ddr50;
+	non-removable;
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	wifi: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
 &soc {
 	firmware: firmware {
 		compatible = "raspberrypi,bcm2835-firmware", "simple-mfd";
diff --git a/arch/arm64/boot/dts/broadcom/bcm2712.dtsi b/arch/arm64/boot/dts/broadcom/bcm2712.dtsi
index a1af86208d9e..6068cb75ef5a 100644
--- a/arch/arm64/boot/dts/broadcom/bcm2712.dtsi
+++ b/arch/arm64/boot/dts/broadcom/bcm2712.dtsi
@@ -285,6 +285,21 @@ gio_aon: gpio@7d517c00 {
 			 */
 		};
 
+		sdio2: mmc@1100000 {
+			compatible = "brcm,bcm2712-sdhci",
+				     "brcm,sdhci-brcmstb";
+			reg = <0x01100000  0x260>,
+			      <0x01100400  0x200>;
+			reg-names = "host", "cfg";
+			interrupts = <GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_emmc2>;
+			clock-names = "sw_sdio";
+			sdhci-caps-mask = <0x0000C000 0x0>;
+			sdhci-caps = <0x0 0x0>;
+			mmc-ddr-3_3v;
+			status = "disabled";
+		};
+
 		gicv2: interrupt-controller@7fff9000 {
 			compatible = "arm,gic-400";
 			reg = <0x7fff9000 0x1000>,